شماره ركورد :
1007873
عنوان مقاله :
بررسي ويژگي هاي فيزيكي و مكانيكي تخته تراشه جهت دار (osb ) ساخته شده از ساقه ذرت
عنوان به زبان ديگر :
The investigation on physical and mechanical properties of oriented strand board (OSB) produced using corn stalks
پديد آورندگان :
كارگرفرد، ابوالفضل سازمان تحقيقات، آموزش و ترويج كشاورزي - موسسه تحقيقات جنگل ها و مراتع كشور - بخش تحقيقات علوم چوب و فرآورده هاي آن
تعداد صفحه :
11
از صفحه :
155
تا صفحه :
165
كليدواژه :
ساقه ذرت , تخته تراشه جهت دار (osb) , مقاومت خمشي , چسبندگي داخلي و خواص فيزيكي
چكيده فارسي :
اين بررسي با هدف استفاده از ساقه ذرت دانه اي در توليد تخته تراشه هاي جهت دار (osb) انجام شده است. لذا از تراشه هاي تهيه شده از ساقه ذرت در 3 اندازه طولي 50، 75 و 100 ميليمتر، 3 نوع چسب اوره، ملامين و فنل فرم آلدئيد و 2 زمان پرس 175 و 185 درجه سانتيگراد به عنوان عوامل متغير و همچنين استفاده از تراشه هاي چوب صنوبر به عنوان شاهد اقدام به ساخت تخته تراشه گرديد. نتايج حاصل از اندازه گيري خواص مكانيكي و فيزيكي تخته تراشه هاي ساخته شده با استفاده از طرح آزمايش فاكتوريل در قالب طرح كامل تصادفي مورد تجزيه و تحليل قرار گرفت. نتايج نشان داد كه تخته تراشه هاي ساخته شده با چسب فنل فرم آلدئيد داراي كمترين مقاومت خمشي، مدول الاستيسيته و چسبندگي داخلي بودند. همچنين نتايج نشان داد كه طول تراشه بر روي كليه ويژگيهاي مكانيكي چند سازه هاي ساخته شده اثر معني داري داشته است و چند سازه هاي ساخته شده با تراشه هاي صنوبر (شاهد) به مراتب از ويژگيهاي مكانيكي بالاتري برخوردار بودند. ولي تخته هاي ساخته شده از تراشه هاي صنوبر در مقايسه با تخته تراشه هاي ساخته شده از تراشه هاي ساقه ذرت با طول هاي مختلف از واكشيدگي ضخامت 2 برابري برخوردار بودند و اين در حالي است كه تخته هاي ساخته شده از تراشه هاي ذرت داراي جذب آب 2 و 24 ساعت بالاتري نسبت به تخته هاي شاهد (صنوبر) بودند. همچنين نتايج نشان داد كه با افزايش دماي پرس از مقدار مقاومت خمشي و مدول الاستيسيته كاسته شده است. ولي مقاومت چسبندگي داخلي تخته تراشه ها با افزايش دماي پرس در سطح معني داري بهبود يافته است. از سوي ديگر با افزايش درجه حرارت پرس كليه ويژگي هاي فيزيكي تخته هاي ساخته شده با افزايش روبرو گرديد.
چكيده لاتين :
The application of corn stalks in the production of oriented strand board (OSB) is investigated. Corn stalks strands were produced in three sizes of 50, 75 and 100 millimeters in length and dried to reach 2% moisture content. Oriented strand boards were made using either urea formaldehyde, melamine formaldehyde and phenol formaldehyde resin, and two press temperatures of 175 and 185 °C. OSB boards using poplar wood strands, 100 millimeters long were also produced as control samples. The results of strength measurements of the boards were statistically analyzed using factorial experiment and completely randomized block design. The grouping of the averages was based on Duncan Multiple Range Test. The results showed that the effect of the resin type on the flexural properties and internal bonding of the boards is statistically significant and boards produced using phenol formaldehyde resin exhibited the lowest modulus of rupture, modulus of elasticity and internal bonding strength. However, the adhesive type did not statistically influence the physical properties. The strand length also statistically influenced the board strength properties and boards made using poplar strands showed higher strength compared to corn stalks strands. The thickness swelling of the poplar OSB was almost twice the values of corn stalks OSB and the water absorption of these boards was lower than of corn stalks OSB. Press temperature adversely affected the modulus of rupture and elasticity, but higher press temperature improved the internal bonding strength. Higher press temperature increased the physical properties of the boards.
سال انتشار :
1397
عنوان نشريه :
تحقيقات علوم چوب و كاغذ ايران
فايل PDF :
7446525
عنوان نشريه :
تحقيقات علوم چوب و كاغذ ايران
لينک به اين مدرک :
بازگشت