عنوان مقاله :
بررسي مقايسه اي تطابق لبه اي روكشهاي موقت ساخته شده با دو نوع ماده موقتي پس از ترموسايكلينگ و نيروي اكلوزالي
عنوان به زبان ديگر :
A Comparative Study of Marginal Adaptation of Crowns Fabricated From Two Provisional Materials, after Occlusal Loading and Thermocycling
پديد آورندگان :
سيفي، مهديه دانشگاه علوم پزشكي مشهد - دانشكده دندانپزشكي و مركز تحقيقات دندانپزشكي - گروه پروتزهاي دنداني , قهرمانلو، احمد دانشگاه علوم پزشكي مشهد - دانشكده دندانپزشكي و مركز تحقيقات دندانپزشكي - گروه پروتزهاي دنداني , مويد، محمد
كليدواژه :
پروتزهاي موقتي , تطابق مارژين , نيروي اكلوزالي , ترموسايكلينگ
چكيده فارسي :
مقدمه: در مواردي كه درمان پروتزي براي بازسازي كل سيستم جونده و اكلوژن بيمار انجام مي گيرد، مدت زماني كه بيمار بايد از پروتزهاي موقتي استفاده كند بسيار طولاني مي شود در اين مدت يك موقتي خوب بايد خصوصيات يك پروتز ايده آل را دارا باشد. بنابراين انتخاب نوع ماده مصرفي براي ساخت موقتي از اهميت ويژه اي برخوردار است. هدف از اين مطالعه آزمايشگاهي، مقايسه تطابق لبه اي روكشهاي موقت ساخته شده از دو ماده موقتي، يكي رزين آكريلي سلف كيور (Tempron) و ديگري رزين كامپوزيتي لايت كيور (Revotek.LC) بود.
مواد و روش ها: در اين مطالعه تجربي آزمايشگاهي تعداد 20 عدد داي برنجي با خط خاتمه تراش شولدر به عرض 1 ميلي متر، ارتفاع و قطر قاعده 7 ميلي متر و زاويه تقاربي 8 درجه تهيه شد. با استفاده از يك كلاهك برنجي براي هر داي يك Coping ساخته و به فرم قبل تراش آماده گرديد. داي ها به دو گروه ده تايي تقسيم و رستوريشن هاي موقتي از جنس مواد فوق به روش مستقيم ساخته شدند. پس از سمان كردن موقتي ها روي داي هاي مربوطه در نقاط علامت گذاري شده ميزان gap مارژين با ميكروسكوپ انعكاسي با بزرگنمايي 100 اندازه گيري شد. بعد از آن تحت نيروي اكلوزال N40 به ميزان 50000 سيكل قرار گرفتند و ترموسايكلينگ oc5-oc55) 3400) سيكل انجام شد. مجدداً اندازه گيري در نقاط علامت زده قبلي صورت گرفت. داده ها تحت آزمون t-student مستقل و با سطح معني داري 5% قرار گرفتند.
يافته ها: يك- اختلاف ميانگين gap مارژين در گروه رزين آكريلي سلف كيور و كامپوزيت رزين لايت كيور قبل از نيروي اكلوزالي و ترموسايكلينگ معني دار نبود 0/19=P. دو- اختلاف ميانگين gap مارژين بعد از نيروي اكلوزالي و ترموسايكلينگ بين دو ماده معني دار نشد (p=0/48) سه- مقايسه ميانگين اختلاف gap قبل از ترموسايكلينگ و نيروي اكلوزالي در دو ماده نشان داد كه كاهش gap مارژين بعد از ترموسايكلينگ و نيروي اكلوزالي در Revotek.lc بيشتر از Tempron بوده و اين اختلاف از نظر آماري معني دار شد (0/042=P).
نتيجه گيري: نتايج حاصل از اين تحقيق نشان داد كه هر دو ماده Tempron و Revotek.lc در شرايط آزمايشگاهي و روش ساخت مستقيم داراي تطابق مارژين خوبي قبل و بعد از نيروي اكلوزالي و ترموسايكلينگ بودند ولي Revotek.lc بعد از نيروي اكلوزالي نتايج بهتري را در كاهش gap نسبت به Tempron داشت.
چكيده لاتين :
Introduction: When the prosthetic treatment of whole masticatory system and patient occlusion are done, the duration
time of temporary restoration increases. In this period, one temporary restoration should have the properties of an ideal
prosthesis. Therefore, the material selection for making a temporary restoration is important. The aim of this experimental
study was the comparison of marginal integrity of temporary crowns made from two types of temporary materials; self
cured acrylic resin (Tempron), and light cured composite resin (Revotek.lc).
Materials & Methods: In this experimental invitro study, 20 brass dies with 1mm width shoulder finishing line were
prepared which had 7mm height, 7mm basal diameter and 8 degree convergence angle. A coping was made from the
brass sleeve for each die to build up the prepared form. Dies were divided into two groups of 10, and then the temporary
restoration was made directly. After cementation of cases on related dies, the marginal gap was scaled by a microscope
with 100 degree magnification. Next, they were put under occlusal load (40N) for 50000 cycles and 3400 cycles of
thermocycling (5-55oc). Finally, the marginal gap was scaled in post dot. Data analysis was done by student t-tests with
95% significance level.
Results: 1. The average marginal gap in self cured acrylic resin before occlusal load and thermocycling was less than
light cured composite resin, but this difference was not significant (P=0.19). 2. The difference of marginal gap between
Tempron and Revotek after occlusal load and thermocycling was not significant (P=0.48). 3. The comparison of gap
before and after thermocycling and occlusal load revealed that marginal gap decreased after thermocycling and occlusal
load in Revotek more significantly than Tempron (P=0.042).
Conclusion: The results of this study showed that Tempron and Revotek lc in both invitro and direct fabrication had
good marginal integrity before and after occlusal load and thermocycling, but Revotek lc revealed a better result in gap
reduction
عنوان نشريه :
مجله دانشكده دندانپزشكي مشهد
عنوان نشريه :
مجله دانشكده دندانپزشكي مشهد